Welcome to a new InTheMail, the series that will touch both your passion for electronics and your bank account at the same time.
Tag: Chip
Voltlog #259 – InTheMail
Welcome to a new InTheMail, the series that will touch both your passion for electronics and your bank account at the same time. We’re going to start with this small white box, which looks very uninteresting from the outside but contains something really nice, it’s a machined aluminium heatsink, designed specifically for the raspberry pi 4 and inside the box you get the two halves of the heatsink plus some mounting screws and silicone thermal pads.
There is a decent amount of aluminium in this heatsink, and we can see it has these rectangular raised islands for contact with the main chips on the board, so this is where the silicone pads will go. This is a completely passive heatsink and that’s what I was looking for but if you want more cooling power these are also actively cooled heatsink. feel like I should test this in a separate video to see how efficient it is when compared to a no heatsink solution which we already know doesn’t work well with the raspberry pi as it gets pretty hot. So we’ll leave this for a future video.
Voltlog #253 – Aneng V01A Multimeter Review & Teardown
Welcome to a new Voltlog, today it’s a multimeter review because we haven’t done one in a while and here I have the Smart Digital Multimeter which sounds like a generic name, no obvious branding on the box but granted it is featuring the multimeter on the box, it’s a color image which is not often seen on these cheap meters. On the back, the meter is shown in full black holster and we get a model number sticker, AN-V01 so this probably indicates the Aneng brand.
We’ve looked at Aneng multimeters in the past in Voltlog #114 and others and I’m gonna say this again, Aneng does not make multimeters, Aneng is just a company that rebrands existing multimeters made by other companies.
Voltlog #247 – InTheMail
Welcome to a new InTheMail, the series that will touch both your passion for electronics and your bank account at the same time. We’re going to start with this small module, at first when I ordered it I didn’t fully understood what it does but now after doing a bit of research for this mailbag it seems this is an immobiliser emulator for the VAG group. So am immobiliser is a security component of your car that will not let the ECU start the engine unless a certain key or token is present. And there might be valid reasons why you might need this emulator, for example if the immobiliser is broken, you can supposably cancel it and start the engine with this emulator or if you exchange the motor/ecu combo once again it might not be possible to use the old immobiliser and so an emulator will help.
It talks over a K-line interface which is something specific to the automotive domain but it’s basically a form of serial interface. At first I thought this was going to emulate some kind of can bus and I was planning to play with it by scanning the bus but now I realize this is useless for me.
Voltlog #229 – What’s The Smallest Digital RGB LED?
Welcome to a new voltlog, today we’re talking about RGB LEDs. Everyone knows and probably uses digital RGB LEDs these days because they’re convenient, you only need a single pin to control then, they can be chained one after the other creating long addressable RGB strings, you don’t have to worry about driving them with constant current, in fact they even have digitally controlled brightness settings so they’re pretty convenient.
Since these are digital, they have a built-in controller chip, and if we take a closer look at one of these LEDs which comes in a 5050 package, we can see the driver chip and the 3 LEDs red, green blue with their corresponding bonding wires. There are two popular drivers chips the WS2812 and the SK6812 and each of these might have different revisions as well. The WS2812 was the original one on the market and then the SK6812 appeared and is considered a clone of the WS2812 but brings some improvements. The SK6812 has doubled the pwm frequency at which it drives the LEDs which is always welcomed as it helps with reducing flicker and also the timing requirements are a bit tighter but existing WS2812 libraries should work fine with the SK6812.