Tag: BLtouch

Voltlog #288 – New BLTouch 3DTouch Plastic Pin Sensor Upgrade

Back in 2018 I installed a Bltouch sensor on my Creality CR10 3d printer and I showed the process in Voltlog #177, that video is one of the most popular videos on the channel and now after using the printer with the upgrade for a couple of years I can clearly say it’s probably one of the best upgrades you can do to your 3d printer and it’s pretty cheap. I won’t go into too much detail about what the sensor does and how to install it because that is discussed in Voltlog #177.

However I did experience a downside after this upgrade, some users are reporting the same problem while others don’t face this issue. It’s important to note I am using a BLtouch clone called 3D touch, purchased from Aliexpress. It’s the type that has a metal push rod through the middle. The issue I’m having is a vibration noise coming from that metal pin vibrating inside the sensor when the printer moves on the Y axis. This issue might or might not be present on a genuine sensor or just another unit which might have tighter tolerances.

Voltlog #239 – Upgrading The CR10 3D Printer With New Print Surface And Bed Insulation

Welcome to a new voltlog, it’s time for another upgrade on my Creality CR10 3D printer, and this time it’s about the print surface. By default this printer comes with a glass print surface which sits on top of the aluminium bed and that has worked fine for most prints and settings I’ve tried but occasionally I would get some adhesion problems and with glass you need to wait until the part has cooled down in order to remove it. Not such a big deal but there is this newer magnetic print surface, which has two parts, you get the bottom part with adhesive that you stick to the aluminium build plate of the printer and you get the top part which sticks magnetically to the other part.

This way, with the top surface I should get better adhesion and when the print is finished I can just remove the print surface from the printer to have it cool down faster or maybe for easier removal because I could just bend the surface to cause the part to unstick.

I’m also going to upgrade the bottom heater of the bed by installing one of these insulation sheets, this should help it reach working temperature faster and maybe it will use less power to keep it at working temperature.

Voltlog #226 – InTheMail

Welcome to a new InTheMail, the series that will touch both your passion for electronics and your bank account at the same time. We’re gonna start with this set of tweezers from Vetus. A few months ago I was considering buying some more expensive electronics tweezers but the good ones are really expensive when you include shipping as well so in the end I decided to give these a try. I’ve had Vetus tweezers in the past and some were good some were bad. This time I asked multiple sellers on Aliexpress if the tweezers are original Vetus or not, some responded and promised their goods are original. Coincidentally or not those who said their products are original also had higher prices. In my experience with suppliers, they never lie about the origins of a product if you directly ask them so I tend to believe that what I have here are genuine Vetus tweezers

 

 

Voltlog #177 – Installing BLTouch Auto Bed Leveling On The Creality CR-10 3D Printer

Today I’m gonna show you how I installed a bltouch sensor on my creality CR10 3d printer. But first to give you a bit of info, if you are a frequent viewer of the channel than you know I have tried a bunch of different sensors, inductive, capacitive but they either didn’t have enough sensing distance to cover the glass I’m using on top of the aluminium bed or they weren’t giving me repeatable results so they all ended up disconnected.

I had a bunch of adhesion problems because I couldn’t level the bed properly, my bed doesn’t look very good, in fact I’m gonna overlay a picture of my bed after the auto bed leveling has been installed and you’ll see it’s far from being flat so it was really difficult for me to print something that was bigger than a couple of cm’s because the bed wasn’t flat.

Then I found this bltouch sensor or more correctly a clone of the bltouch sensor on aliexpress for just $14 and I said why not, let’s try this one as well and ordered one. And boy was I impressed how much better the printing got after installing it.

Voltlog #167 – InTheMail

Welcome to a new InTheMail the series that will touch both your passion for electronics and your bank account at the same time.

Here are links to all the products shown in this video: